lite-on technology corporation property of lite-on only features * high intensity. * popular t-1 3/4 diameter package. * selected minimun intensities. * general purpose leads. * reliable and rugged. package dimensions part no. lens source color LTL-4233-032A green diffused green notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 1.0mm(.04") max. 4. lead spacing is measured where th e leads emerge from the package. 5. specifications are subject to change without notice. part no. : LTL-4233-032A page : 1 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only absolute maximum ratings at t a =25 parameter maximum rating unit power dissipation 100 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 120 ma continuous forward current 30 ma derating linear from 50 0.4 ma/ reverse voltage 5 v operating temperature range -55 to + 100 storage temperature range -55 to + 100 lead soldering temperature [1.6mm(.063") from body] 260 for 5 seconds part no. : LTL-4233-032A page : 2 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only electrical / optical characteristics at t a =25 parameter symbol min. typ. max. unit test condition luminous intensity i v 5.6 19 mcd i f = 10ma note 1,4 viewing angle 2 1/2 36 deg note 2 (fig.6) peak emission wavelength p 565 nm measurement @peak (fig.1) dominant wavelength d 569 nm note 3 spectral line half-width ? 30 nm forward voltage v f 2.1 2.6 v i f = 20ma reverse current i r 100 a v r = 5v capacitance c 35 pf v f = 0 , f = 1mhz note: 1. luminous intensity is measured with a light sensor and filter combination that approximates the cie (commission intern ational de l'eclairage) eye-response curve. 2. 1/2 is the off-axis angle at which the luminous in tensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. the iv guarantee should be added 15%. part no. : LTL-4233-032A page : 3 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : LTL-4233-032A page : 4 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only features * compatible with radial lead automatic insertion equipment. * most radial lead plastic lead lamps av ailable packaged in tape and folding. * 5mm (0.197") formed lead spacing available. * folding packaging simplifies handling and testing. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 20.0 0.787 21.0 0.827 feed hole to overall component height h2 28.3 1.114 29.9 1.177 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead location p1 4.4 0.173 5.8 0.228 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape width w1 14.5 0.571 15.5 0.610 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748 part no. : LTL-4233-032A page : 5 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).c onsult liteon?s sales in advance for information on applications in which exceptional relia bility is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their origin al packaging are used within three months. for extended storage out of their original packagi ng, it is recommended that the leds be stored in a sealed container with appropriate desiccan t or in desiccators with nitrogen ambient. 3. cleaning use alcohol-based cleaning solvents such as is opropyl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, leave a minimum of 2mm clearance from the b ase of the lens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame dur ing soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 300c max. 3 sec. max. (one time only) pre-heat pre-heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 10 sec. max. note: excessive soldering temperature and/or time mi ght result in deformation of the led lens or catastrophic failure of the led part no. : LTL-4233-032A page : 6 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only 6. drive method an led is a current-operated device. in orde r to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in seri es with each led as shown in circuit a below. circuit model a circuit model b led led (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i-v characteristics of those leds part no. : LTL-4233-032A page : 7 of 8 bns-od-c131/a4
lite-on technology corporation property of lite-on only 7. reliability test classification test item test condition reference standard operation life ta= under room temperature as per data sheet maximum rating * test time= 1000hrs (-24hrs,+72hrs) mil-std-750d:1026 (1995) mil-std-883d:1005 (1991) jis c 7021:b-1 (1982) high temperature high humidity storage ta= 655 rh= 90 ? 95% test time= 240hrs2hrs mil-std-202f: 103b(1980) jis c 7021 : b-11(1982) high temperature high humidity reverse bias ta= 655 rh= 90 ? 95% vr=5v test time = 500hrs (-24hrs, +48hrs) jis c 7021 : b-11(1982) high temperature storage ta= 1055 * test time= 1000hrs (-24hrs,+72hrs) mil-std-883d:1008 (1991) jis c 7021:b-10 (1982) endurance test low temperature storage ta= -555 * test time=1000hrs (-24hrs,+72hrs) jis c 7021:b-12 (1982) temperature cycling 105 ? 25 ? -55 ? 25 30mins 5mins 30mins 5mins 10 cycles mil-std-202f:107d (1980) mil-std-750d:1051(1995) mil-std-883d:1010 (1991) jis c 7021: a-4(1982) thermal shock 105 5 ? -55 5 10mins 10mins 10 cycles mil-std-202f:107d(1980) mil-std-750d:1051(1995) mil-std-883d:1011 (1991) solder resistance t.sol = 260 5 dwell time= 10 1secs mil-std-202f:210a(1980) mil-std-750d:2031(1995) jis c 7021: a-1(1982) environmental test solderability t. sol = 230 5 dwell time= 5 1secs mil-std-202f:208d(1980) mil-std-750d:2026(1995) mil-std-883d:2003(1991) jis c 7021: a-2(1982) 8. others the appearance and specifications of the product may be modified for improvement, without prior notice. part no. : LTL-4233-032A page : 8 of 8 bns-od-c131/a4
|
